Spa Drains:
From 1995 to
circa 1998 Jacuzzi used the "Large" drain. In 1998
they switched to the "Small" drain. When you order,
email me and I'll give you a shortcut that will
speed up and ease your replacement.
Small Spa
Drain
Large Spa
Drain
late models
early models
2540-303
2000-035
$11.90
$26.50
Jacuzzi Front Load Filter Cabinet:
If the leak is at the seal where
the filter cabinet bonds with the shell, try this first. Drain the spa. Let
dry. Remove the filter housing frame on the water side by snapping off the
frame. This will expose the white flange. Apply a bead of clear
silicone on the water side and massage the silicone between the flange and
the shell. Snap the frame back on and fill. Many times this will solve the
leak.
If the leak is from the cabinet itself or plumbing, you will need to
replace the cabinet. Besides offering the cabinet, we offer a bracket that
makes reinstalling easier. That bracket is optional. If you will have
someone working with you, you don't need the bracket but either way it's a
lot easier using the bracket.
These are OEM replacement
parts used by Jacuzzi Whirlpool Spas from early 1990's to 2001
2540-385
Filter Housing
2000-201
Rubber Seal On Top of Filter Housing
2540-400
Grommet Seal for Electronic Temp Sensor
2000-040
Filter Housing Bracket
2000-045
Filter Weir
Frame
2540-375
Filter Basket
$49.00
$2.49
$2.49
$59.00
$29.00
$5.00
Heater Repair Coupling:
If your heater coupling breaks or leaks,
you can replace just the coupling and seal. This kit includes both but only
for one side. If both ends leak, then you will have to replace with two.
Repair
Heater Coupling and Gasket
$14.90
Jacuzzi Patented Jets:
Below you will see the most common complete jet assemblies used in Jacuzzi Whirlpool Spas.
If the jet or piping at the jet is damaged, you have to remove the complete
jet and replumb the new jet with PVC glue. Some plumbing parts are standard
PVC plastic parts you can purchase from any hardware store. Others are
specific to spas. Go to: Plastic Spa Fittings for
spa specific parts. Also, check below for nozzle and parts.
All Jet Housings Are Gray
Jacuzzi's Patented BMH Jet
AMH Jet
Jacuzzi's Patented HTC Jet
Jacuzzi's Patented HTA Jet
(2 5/8" diameter hole)
(3
1/4" diameter)
(3 1/4"
diameter hole)
(4
1/4" diameter hole)
Complete Assembly
Complete
Assembly
Complete
Assembly less Knob
Complete Assembly with Knob
Knob Only
$29.00
$45.50
$59.75
$61.75
$3.00
Discontinued--Can Use HTC found to right
Below are the Most Common
Repair Parts for the Above Jets. The above comes as an
assembly. That is ONLY the body and parts internal to the body. Nut,
spacer, and other fittings are not included because they usually are
reusable or easy to obtain locally. We include these choices for parts
not common.
Barb Air Line
90 Barb Elbow
T Barb Elbow
Spacer
Nut
For BMH Shown Above
For HTC Shown Above
For HTA Above
BMH Choice One
BMH
Choice Two
BMH
Choice Three
Includes nut, barb air line elbow, and
barb water line elbow
Includes nut, barb air line elbow, and
barb water line "T"
Includes nut and glue air line adaptor
For spas with Barb Fittings
For spas with Barb Fittings
For spas with Glued Fittings
$5.99
$6.99
$3.99
HTC Choice One
HTC Choice Two
Includes Nut, Spacer, Plug, and barb
air line adaptor
Includes Nut, Spacer, Plug, and air
line adaptor
For Spas with Barb Fittings
For Spas with Glued Fittings
$8.99
$8.99
HTA Nut and Spacer
$8.99
Jacuzzi Jet Assembly Nozzles Only:
This is the strangest thing to happen because the cause is likely NOT the
air control but the jet nozzle at the jet assembly. What can happen is the
jet nozzle fails to create a suction at the back of the jet housing and this
forces water UP the air line. To correct, you need to replace the nozzle.
Usually all you have to do is remove the old nozzle and install the new. You
can reuse the gasket, screws, and retaining ring. We do offer retaining ring
and gasket as option but they are not normally replaced.
HTC Jet Nozzle
HTA Jet Nozzle
AMH Nozzle
2000-164
Package of Six
Retaining Ring and Gasket Only
2000-154
(pictured)
Package of Six
Package of Six and End Knobs
End Knob Only
Retaining Ring and Gasket Only
14.90ea
59.00/6
7.98
19.90ea
79.00/6
94.00
$3.00ea
$7.98ea
Neck Jet: ONLY for Z-255
2000-657
$29.00
Spa Light Len Assembly:
Cracks at light lens usually require replacing the
lens. This is the lens and nut.
Light Lens w / Nut
$19.90
Air Control Assembly:
(see info on nozzels directly above before
ordering this)
Gray Knob
Graphic Gray Ring
Gray Panel
2540-200
2540-203
2530-150
2540-201
2540-202
2000-220
$18.50
$2.90
$2.49
$3.49
$4.99
$9.90
Jacuzzi Patented "J' and
"k" Pump:
When the pump leaks, it's wisest to
replace the complete pump. The reason is that the leak can come from the
seal, or impellor or pump bracket. Rather than try this and that, we
recommend that you replace the whole pump. That is why we offer the pump as
a complete kit.
All kits include
the above parts plus the pump face (volute) shown below.
CC-1JP
CC-2JP
CC-3KP
This is the
pump used on two pump spas with identical pumps. It's a 240v motor,
single speed.
This is the
pump used on single pump, two speed spas. It's for a 110v motor.
This is the
pump for spas with a 3hp K-Pump system. The pump uses the pump face
shown above.
$109.00
$109.00
$139.00
Repair
Unions plus seal/oring
x2
Flange and 2 Gaskets
for Older White Pump
Union for J-Pump;
comes with new oring
2000-010/2000-011
2000-170
$9.99
16.00
Rainbow
Spout Cover (gray)
Rainbow
Spout Assembly
2540-220
2540-221
$6.99
$29.00
Suction Fitting:
In the footwell
of your spa are one to three square covers where the
water is pulled into the plumbing system. This is
the replacement covers that include the gray cover
and gasket. Grey is the color the plastic originally
came in.
Gray Suction Cover
2" Screw for Above
Complete Assembly less Cover
2540-324
2570-066
2540-325+
$8.90
$.99
$14.40
Ozone Fitting
2540-335
$14.90
Vent Lines:
The vent lines are designed to either allow the water to drain more
completely when draining or to avoid air locks when filling. This kit
supplies two 90 degree compression fittings and one straight compression
fitting and the vent hose. You cut the hose to fit and use what fittings you
might need. Keep the remaining parts for later..
Please Note: The vent
line is the same size as the waterline to your icemaker. You could use
that instead.
